Intelimax Firmware upgrade

Is this email not displaying correctly? View it in your browser.

INTELImax Firmware Update

product: INTELImax

product Code: MA-2015

release version: 0.1.56

Details

maXconnect Remote Monitoring Support:

Support added for remote monitoring and control via MaxConnect portal
maXconnect is a cloud based M2M management portal which allows you to access, monitor and control 3G/4G Maxon devices securely. With maXconnect you can access real-time data from your devices, monitor their status and location. Utilise complete functionality by controlling your devices anywhere, anytime. This one stop portal is an access point to manage your 3G/4G assets securely and remotely.

Stability:

CSD bug fixes to module firmware (module upgrade required)
A major CSD issue was resolved with direct contact and sustained work with Huawei. This improves the stability and reliability of CSD calls considerably. This functionality will require both a base firmware and module firmware upgrade.

Module monitoring
In addition to the module firmware upgrade the module control and monitoring abilities of the firmware have been improved to reduce any chance of module lock up.

Reverting to defaults
Maxon identified an issue where some Intelimax modems would revert to factory defaults under particular situations. This has now been resolved.

Useability:

Reduced boot time
The boot time of the Intelimax when in serial modem mode has been reduced to under 40 seconds.

The LED functionality has been improved to give the user further information and debugging help during installation and use.
Both the Power and Data LEDs can now be used to determine the signal strength and connection status of the modem

Remote configuration of Dynamic DNS settings
The Dynamic DNS settings can now be configured via SMS. This means that if a device in the field has is using the ‘telstra.extranet’ APN then the modem’s public WAN IP address can configured to update to a Dynamic DNS account for remote access. (The WAN IP address can also be accessed directly via SMS).

Periodic reset of 26 hours
A periodic reset setting of 26 hours allows for the Intelimax to reboot itself if an external daily reboot trigger doesn’t occur.

SMS on hard boot
The Intelimax can now be configured to send an SMS when it first boots up. This SMS will only be sent if the modem goes through a hard reset as controlled either by a user or external equipment trigger.

Security:

SNMPv3 support has been added
SNMP (Simple Network Management Protocol) is an internet-standard protocol for network enabled devices such as switches and routers allowing easy access to vital information about multiple network components all in one place. SNMPv3 takes the functionality of SNMPv1 and SNMPv2 and adds the benefits of cryptographic security.

Interfacing to Legacy Equipment:

Modem emulation functionality allowing for IP connectivity to an end device that only supports CSD (Circuit Switched Data)
This functionality eases the transition from CSD-based to IP-based communications to your remote devices. Legacy equipment that is configured to dial out a CSD connection to the control centre don’t have to be redesigned or reconfigured. The modem will seamlessly establish an IP connection to the control centre upon receipt of the dial out AT command then can revert back to a TCP server mode for remote connections back in.

Click below to register your Update request.

Security

SNMPv3 support has been added. SNMP (Simple Network Management Protocol) is an internet-standard protocol for network enabled devices such as switches and routers allowing easy access to vital information about multiple network components all in one place. SNMPv3 takes the functionality of SNMPv1 and SNMPv2 and adds the benefits of cryptographic security.

Remote Monitoring

Support added for remote monitoring and control via MaxConnect portal. maXconnect is a cloud based M2M management portal which allows you to access, monitor and control 3G/4G Maxon devices securely. With maXconnect you can access real-time data from your devices, monitor their status and location. Utilise complete functionality by controlling your devices anywhere, anytime.

Data Logging

If you are thinking of changing over from Circuit Switch Data (currently being phased out ) to Packet Switched Data ( faster and more reliable) however, the data logger you are using is outdated and can only dial a phone number. With the latest upgrade, the Intelimax can be configured to send data to an IP address when the logger dials a phone number.

P.O. Box 1 Revesby North NSW 2212 Australia
P +61 2 8707 3000
F +61 2 8707 3001
E sales@maxon.com.au

If you no longer wish to receive emails from this advertiser, please unsubscribe